Japanese steel hot water bottle 萬年 Mannen MY-7204 — 2.4 L, made in Japan
The Japanese metal hot water bottle, the one called 湯たんぽ (yutanpo): you pour in boiled water, screw down the brass cap and slip it into the bed before you turn in. 2.4 litres in a ribbed shell of 0.5 mm galvanised steel, which warms over its whole surface. Nothing to plug in, nothing burning inside, and the air in the room stays as it was. It comes from the workshops of 尾上製作所 (Onoe Seisakusho) in Himeji, under the 萬年 (Mannen) brand, and carries the SG mark of the Japanese product safety association. 290 × 220 × 80 mm, around 630 g empty. Cover not supplied.
There is a point in winter when you put off going to bed because you know the sheets will be cold. A hot water bottle slipped under the covers a while beforehand settles that: by the time you get in, the place is already warm, and it has warmed the mattress instead of you.
This is the Japanese take on it, the 湯たんぽ (yutanpo): not a rubber bag but a piece of metal. Pick it up before you fill it. Six hundred and thirty grams, a bare shell that rings when you tap it with a finger, galvanised steel sheet folded into a 2.4 litre container. Apart from the rubber seal in the cap, there is no plastic on it.
The routine
You boil water in a kettle or a pan. You pour it in through the neck. You screw the cap down onto its seal, good and tight, wipe the shell dry and carry it to bed. No socket, no lead, nothing to recharge or keep an eye on: the only energy spent is what it took to boil the water.
2.4 litres, and that is deliberate
That is a lot of water for a hot water bottle, and that is the whole point: the more water there is, the longer it takes to cool. At 290 × 220 × 80 mm it is about the size of a large, fairly thick book — enough to cover both feet rather than one.
The ribs are not decoration
Half a millimetre of flat sheet steel buckles at the first knock. Ribbed, folded into troughs and crests on both sides, it holds up: that is what keeps the wall straight when 2.4 litres of boiling water goes in. The ribs do a second job, since they increase the surface area in contact with the air: the heat comes off over a wider area than it would from a smooth wall.
The brass cap
This is the part that does the most work: it is screwed and unscrewed every evening, on metal that is hot and wet. It is brass rather than plastic, and its black rubber seal is supplied — it sits flat in the groove of the cap and can be replaced once it hardens. There is nothing else to maintain: no electronics, no moving parts.
Bed, feet, desk
In bed it goes at your feet, and warm feet do half the work: the rest follows. In winter, at a desk, it sits under the table against your calves or on your lap, when heating a whole room for one person makes no sense. You feel the metal straight away: the heat passes through the wall without delay and the shell warms over its whole surface, not just at the cap end.
Nothing burns inside it — you pour in boiling water and that is all — so there is no risk of carbon monoxide poisoning, unlike a fuel-burning heater. And the air in the room stays as it was; that is the manufacturer's first selling point, 空気を乾燥させない暖房, "heating that does not dry out the air". That is the difference from a fan heater, which leaves your throat dry.
Himeji, and the SG mark
It comes from the workshops of 株式会社尾上製作所 (Onoe Seisakusho), in Himeji, Hyōgo prefecture, under the 萬年 (Mannen) brand. The body carries the SG mark of the 製品安全協会, the Japanese product safety association, which grants it only to items that meet its standard. It is not a logo printed on the box, it is an inspection.
Read this before you fill it the first time
- Never heat it directly. The product label says so in Japanese: 直接加熱しないでください. If you put it on a gas ring, an induction hob, a stove or a fire with the cap closed, the pressure inside rises and it can burst. Boil the water separately, then pour it in.
- The cover is not supplied. Once filled, the shell is too hot to rest against bare skin: it needs covering before it goes into the bed. The manufacturer states that a 290 × 350 mm cover fits it; a folded pillowcase or a thick jumper will do until you find one.
- A hot water bottle needs replacing, generally every two years: the seal ages and the metal is worked with every cycle. Check the cap seal, and check that it still holds water, at the start of each cold season.
- Screw the cap fully home before moving it, check that it is not seeping, and pick it up with a cloth while it is full.
Specifications
- Manufacturer: 株式会社尾上製作所 (Onoe Seisakusho), Himeji, Hyōgo prefecture
- Brand: 萬年 (Mannen) — model MY-7204
- Japanese name: トタン湯たんぽ 2.4L (galvanised sheet hot water bottle, 2.4 L)
- Capacity: 2.4 litres
- Dimensions: 290 × 220 × 80 mm
- Empty weight: approximately 630 g
- Material: galvanised steel (亜鉛鉄板), 0.5 mm sheet, ribbed body
- Brass cap, black rubber seal supplied
- SG mark of the 製品安全協会 (Japanese product safety association)
- Made in Japan (日本製)
- Cover not supplied
- Parcel: 36.9 × 23 × 7.8 cm
An object that does one thing, with no settings and no electronics, and that comes back out every year on the first properly cold evening.
- Reference4907797072042
- EAN134907797072042
Encrypted and protected transactions
Shipped from Japan with tracking
Imported directly from Japan, genuine products
Comments (0)
Your review appreciation cannot be sent
Report comment
Report sent
Your report cannot be sent